NU1500 Components

HRV Stand:

The all-aluminum HRV stand is designed to support the HRV Exchanger in a vertical position.  Each wall panel is designed with a 5 layer thermal break design with a foam core.  The outside of the foam core panel is all aluminum with a white polyester finish.  The foam core panel is attached with industrial strength adhesive using stainless steel fasteners.  Each panel is 1" thick.  Four support legs lift the stand 6" off the ground for connection to drains.

stand1 img_2331

Controls:

A typical indoor pool requires both temperature control (between 75 and 85 degrees) and humidity control (between 50% and 60% relative humidity).  The NU-1500 temperature and humidity control system is designed to create an outdoor environment in your indoor pool. Includes simple LED viewer. 24 volt powered.

dsc00993Temperature Control Module dsc00987Humidity Control Module

MERV-8 Outside Air Filter:

A special washable outside air filter assembly cleans the incoming outside air before it enters the HRV exchanger.  This uniquely designed filter contains four (4) stages of cleaning all in one frame.  It is contained within an all-aluminum extrusion box frame with a slide out filter sub frame.  The NU-1500 has a side access door for easy access to the filter.

  • Washable filter comes with a 10 year warranty.
  • Filter is designed for easy soap and water cleaning.
  • Contractor installs the filter between the outside air connection in the building and the inlet connection on the supply air blower.
dsc01026

BI-15 Airfoil Blowers:

Supply and exhaust airfoil blowers are designed with the latest state of the art wheel.  Each blower is comprised of a 16 gauge all welded housing and a backward incline all welded wheel.  Both housing and wheels are coated with Heresite to protect the fans from rust and corrosion.

  • 1 HP high efficient ODP motors running on 230 volts/3 phase.
  • Motors draw .8 amps at full operation.
  • Noise is contained in housing and is under 65 DB.
  • Tested and certified for air performance by AMCA.
  • Fan weight = 200 lbs. each
fanview-1 fanview-2

VFD Fan Micro Drives:

Each airfoil blower is supplied with a VFD fan micro drive inverter.  Each drive contains a PID loop control and allows the supply blower speed and flow to be 10% less than the pool exhaust blower airflow.  This offset maintains the pool room at a negative pressure at all times.

  • Converts 120 volt AC input power to 230 volt/3 phase fan control power.
  • Has a LED screen for visual access to set points and values.
3xa37_as01

Anti-vibration Mats:

Each airfoil blower is supplied with a special rubber anti vibration mat with caution strips.  The caution strips warn operators that they are approaching rotating machinery.

 

vibration mat vibration mat

Micro Channel HRV Heat Exchanger:

  • All polymer construction
  • Over 900 square feet of surface for exchange
  • Low pressure drop
  • Fused & welded polymer case
  • Will not rust or corrode
  • 20 year warranty
  • Air flow range = 900 to 1,600 CFM
  • Requires less heat
  • 87% thermal effectiveness
  • Pressure drop .20 to .35
  • 34% latent recovery
  • Weighs only 280 lbs.
  • Self-cleaning micro tube design
  • Air speed designs are under 1.56 FPM
  • Media speed at 1,500 CFM airflow
dsc01017

 

 

   

Complete Component Listing:

  • (1) NU-1500 HRV exchanger
  • (1) 48" x 25" x 31" HRV stand
  • (1) Air filter box with filter
  • (2) BI-15 Airfoil blowers
  • (2) 1HP 230v/3ph/60Hz VFD fan micro drives/Nema 1 casing
  • (2) Anti vibration mats
  • (1) Wiring diagrams
  • (1) Service manual

Controls:

  • (1) Wall mounted temperature controller
  • (1) Wall mounted humidity controller
  • (2) Wall plates
  • (1) 120/24 Control transformer
  • (1) Humidity duct sensor
  • (1) Duct insertion support
  • (1) Power transformer
 

Download the technical brochure in our resources section

Company News

Engineering Upgrade Announced

NuClimate Air Quality Systems, Inc is pleased to announce that it will be releasing new versions of its QLS (24" x 48") and Q1/Q1L (24" x 24") 1-way blow Chilled Beam unit during the 1st quarter of 2011.  This engineering upgrade will allow contractors to easily select left and right hand configurations to meet installtion demands.

Release of 2-Way Blow Induction Beam

NuClimate Air Quality Systems, Inc is pleased to announce that it will be releasing a 2-way blow Induction Beam unit during the 1st quarter of 2011. The unit will be available in two sizes 24" x 24" and 48" x 24". It will feature a fully functional drainpan in case latent conditioning is necessary. The unit will be available in 2 and 4 pipe configurations.

NuClimate announces Partnership with Carrier

June 1, 2012 NuClimate Air Quality Systems, Inc. is please to announce a new exclusive partnership with Carrier Air Conditioning for the OEM supply of its Chilled/Induction Beam line. Carrier's expertise and engineering tools will take this product to the next level! Stay tuned for more and check out our representative map for new representatives around the US and abroad.

Follow NuClimate on Facebook, Twitter & Linked-In

Follow NuClimate now on facebook and twitter and Linked-In!

http://twitter.com/NuClimate

http://www.facebook.com/NuClimateAirQualitySystems?ref=hl#!/NuClimateAirQualitySystems

http://www.linkedin.com/company/nuclimate-air-quality-systems-inc-?trk=nav_account_sub_nav_company_admin